Clik here to view.
Using Assembly Parameters in Part Models for Part Identification (Both Simple...
I have a problem with Family Table Multi-Body parts. Our manufacturing group requires the part number of each of our sheet metal parts to be stamped/etched onto the part itself when the part is being...
View ArticleClik here to view.
Trouble With Offset Lines - Creo Parametric 3.0 M050
Community, When I make offset lines going from the HiLok to the hole in the skin, it works fine. But when I try to make the final offset line from the Collar to the hole in the skin, the line always...
View Articlesketch relations using a saved analysis
In an assembly I have one sketch which is a rectangle that surrounds a couple parts that are stacked. I use the analysis / measure / length tool to get the length of that sketched curve. I save this...
View ArticlePoint on Center of Any Surface?
Is there a way in Creo to place a point, axis, or coordinate system at the U/V midpoint of any single surface?Creo can place a point "on center" of a circular surface, but I would like to do the same...
View ArticleClik here to view.
automatique table in one DRW for variants part created using inheritance feature
Hello the community, Everybody knows how to generate an automatic table in a drawing based on a family table. But is that possible to do that also for a set of variant part which was created using...
View ArticleAnimation of Water in a Tank
Hey Everybody, How can I animate a reservoir with a decreasing fluid level? I thought that I could just create an assembly with a reservoir and a family table of three different heights of fluid. I...
View ArticleHelp with curve and meaning of symbol in parametric
Hello i need help with an easy task. I should do an curve witch i think exist of three arcs, but it should be done Exactly like in the first Picture(same symbols, same numbers and so on). As u can see,...
View ArticleClik here to view.
Csys size?
Folks, I have a dumb question regarding Creo 2, M100. Is there a way to enlarge the csys? My eyesight is getting worse with age and I find it increasingly difficult to see these puppies. Best regards,...
View ArticleCan we design Multi Body Part../?
Hello, I want to design Mouse in creo, i done outer body using surface..Now I want to divide in multi part.. Its possible in Creo..?If yesh then how can we do it..?Same thing can do in SolidWorks,its...
View Articlepro_mp_mass is not updated
Hi, parameter pro_mp_mass is not updated even when I compute mass properties.This on is updated when I change some dimensions but not the parameter.The only solution I've found it to go in prepare...
View ArticleClik here to view.
What does "Topology changes detected" mean in the trail file?
I was reviewing a trail file investigating an issue, and came across the message below several times: !%CIRestoring XXXXXXXXX_INST feature 8 out of 21 ...!Topology changes detected; regenerating DATUM...
View ArticleImported AutoCAD .dwg not visible
Hello everyone. I am having this problem since I have upgraded from M070 to M100 version of Creo 2. Usually when I imported drawings all the ACAD colored layers were visible in the Creo model. Now the...
View ArticleClik here to view.
Spin command
I know that if I use the MMB I can spin the part around, if I hold SHIFT I can pan, and if I hold CTRL I can either zoom in and out or rotate the part on a forward facing axis. I want to know if there...
View ArticleThis is the Best Cad software I have ever seen in my life!
This is the Best Cad software I have ever seen in my life!I would llike to tell you Why1. It' s better that AutoCa... because it can draw a line without command2. It' s better that AutoCa...because it...
View ArticleOver-riding show-erase dimensions in a Creo 2.0 drawing
Hi, I have a detailed drawing in Creo 2.0 which had 10 show-erase dimensions. Out of these, for some design requirement, I need to over-ride 5 of the show-erase dimensions. Is it possible? If yes, what...
View ArticleCreate DXF
Is there a way to create a 2D DXF of a part automatically? We have a template with only 1 view with an orientation DXF. Now I would like to make a mapkey so automatically the drawing is created out of...
View Articleprb affichage section en mode ombragé CREO3
Bonjour,Impossible pour nous d'afficher une section en mode ombragé dans un pièce (.prt) sur CREO3 La section s'affiche en dans tous les autres modes e visualisation (sans ligne cachée, lignes cachées...
View ArticleModel change log?
I'm not sure if this is the best place to post this, but I'm trying to find some advice. My company is still using Pro/E Wildfire 4.0 and we are running into problems with multiple sites working on...
View ArticleClik here to view.
How to retain entity characteristics?
In my base model I can change the color of the geometry I am working on. When I move this model into another model using Merge Inheritance or Copy Geom it loses it's color characteristics. I know there...
View Article