General Blend in Creo Parametric 2.0 Missing
Hi, How to create a General Blend in Creo Parametric 2.0, I want to provide parallel distance and angles in two directions as well to my 2nd section. Pls Help. ThanksShashank Sharma
View ArticleClik here to view.
Conversion of complete surface step file to solid step???
Hello All, Struck again I have a step part but all the features are in surfaces & I would like the part to be solidified(No inner details should be available), any advice would br appreciated...
View ArticleClik here to view.
Creo 2.0 M030 planes and there names intersecting?
below are the screen shots of the two displays. In Pro|Engineer wildfire 3.0 the planes and there names are arranged neatly, whereas just have a look at the planes and the names in Creo 2.0 screen...
View ArticleClik here to view.
How to create a nozzle removing material with variable section sweep?
Hi! I need some help on below:I am working on a plastic casing that has two main components as shown in the very first picture. There is already an inner cavity (turbine shaped cut to accept water)...
View ArticleWhat file format from a Romer Coordinate Measuring Arm can be imported into...
What file format from a ROMER Coordinate Measuring Machine can be imported into Wildfire4 that will allow you to append to if needed and allow youto create a sheet metal flat. I am basically wanting to...
View ArticleCreo Direct Modeling Simplification functionality
I love the fact of the simplification functionality. Loading a model from ModelManager and you have the possibility to select a Simplify part instead of the complex, detailed part is really the...
View ArticleHow to avoid double intersection points.
Everybody, I have a situation where i need a point at the intersection of a cycinder surface, with two datum planes witch are normal to each other.This wil create two possible intersection points on...
View ArticleSCELETON FROM IMPORTED FILE - RESETTING THE ORIGIN
Dear all, I'm busy with a scructure where I use a sceleton that comes from an 'imported wireframe/surface designfile. I have cleaned up the designfile first, removing all I din't need but putting it...
View Articlependulum on the moon
Inspired by http://ptc.co/i1TYl I created a chaotic pendulum with ProE WF5, and recorded a DYNAMIC simulation.I've created a motion skeleton and then attached parts (steel) to each skeleton-body.This...
View ArticleClik here to view.
protk_wf4.dat configuration error
Dear PTC users I prepared a new configuration.pro for new project, i am facing the new error while opening creo/elements pro 5.0. I have attached some screen shots below, Kindly view it and help me....
View ArticleClik here to view.
Questions regarding automatic feature creation and making cuts at feature...
I have a skeleton model consisting of only datum points and curves (Picture 1). Every datum curve represents a tube or rod with 1" OD, and my plan for creating the tubes or rods is to make a swept...
View ArticleClik here to view.
Help! How to extrude/stretch 80/20 cad model?
I downloaded an 80/20 CAD Model off of 3d Content Central, however it's too short. I need it to be 17.5"s instead of a measly 12. Is there anyway to extrude or stretch the model to fit my wishes?
View ArticleSketches and references based on assembled parts: Good or Bad idea?
There have been several times, when I come to a dead end, that I design parts' features based on assembly file. For example, if part A has a peculiar curve or section, I fisrt assemble that part B ,...
View ArticleWhere used?
Is there a way to see in which assembly’s a part is being used? I have creo parametric 2.0. I don’t seem to have PDM link what is explained in the question of Mike Minsterketter.
View ArticleClik here to view.
modeling with a shared (and linked) 'sketch'
Hi all, Small question, I have a skeleton in Creo I use to extrude rods on the wireframe (orientation is in all directions, under all dieffertent angles)These rods have all the same section, but could...
View ArticleAnimation interpolation problems
I am trying to create an animation in Creo 2.0. To start with I am just trying to create a simple orbit animation and to do this have created four views at 90 degree rotation points and set them...
View ArticleClik here to view.
Screen Resolution is not optimistic in Creo Parametric
Hai, Everyone i got struck with some serious issues,,which PTC team fail to Solve and gave me a some pages of PDF(hardware notes) were very adament by thier rules and regulation ,,to fix the Megapixel...
View ArticleOpening Older File Iterations - Using FILE>OPEN dialog box
Hi all, I'm stuck. I want to be able to open older CAD iterations by inputting the the information in the File>Open dialog box directly. I can't recall the correct syntax to get this to work....
View ArticleCreate wavy washer in Pro E 4.0
Looking to try to create a wavy washer and a washer with radial teeth cut into it? How would I go about doing this? Thanks. Jon.
View Article